文章摘要
邢洁芳,倪晓宇,张 杰,陈杜鹃.基于有限元法的CTP成像滚筒及版材的数值仿真[J].包装工程,2011,32(1):25-28.
XING Jie-fang,NI Xiao-yu,ZHANG Jie,CHEN Du-juan.Numerical Simulation of CTP Imaging Drum and Plate Based on ANSYS[J].Packaging Engineering,2011,32(1):25-28.
基于有限元法的CTP成像滚筒及版材的数值仿真
Numerical Simulation of CTP Imaging Drum and Plate Based on ANSYS
投稿时间:2010-10-09  修订日期:2011-01-10
DOI:
中文关键词: CTP  成像滚筒  有限元  ANSYS
英文关键词: CTP  imaging roller  finite element  ANSYS
基金项目:江苏省制浆造纸科学与技术重点实验室开放基金项目(200922)
作者单位
邢洁芳 南京林业大学 江苏省制浆造纸科学与技术重点实验室, 南京 210037 
倪晓宇 南京林业大学, 南京 210037 
张 杰 南京林业大学 江苏省制浆造纸科学与技术重点实验室, 南京 210037 
陈杜鹃 南京林业大学 江苏省制浆造纸科学与技术重点实验室, 南京 210037 
摘要点击次数:
全文下载次数:
中文摘要:
      利用有限元分析软件ANSYS建立CTP成像滚筒的几何模型与有限元模型,选择接触单元模拟版材和滚筒表面之间的关系,以滚筒本体、滚筒与版材组合以及对滚筒内部吸真空的3种组合下进行有限元静力分析,获得滚筒自身变形对版材影响的大小,以及滚筒内抽吸真空对版材和滚筒变形的影响。结果表明,3种情况下滚筒和版材的最大变形量及位置均有所不同。其中,吸真空组合分析说明,版材在与滚筒表面密合状态下变形情况随从滚筒,滚筒表面的导槽对版材变形会产生一定影响,真实反映了工作状态,研究结果可以为CTP成像滚筒的设计与优化提供理论依据。
英文摘要:
      Geometric model and finite element model of CTP imaging drum are established using finite element analysis software ANSYS. The relationship between plate and roller surface was simulated by selecting contact element. The static characteristics of combination among drum body, roller and plate as well as additional vacuum suction inside cylinder were analyzed. The results showed that the maximum deformation and location of roller and plate are different in the three cases. The analysis of vacuum suction combination showed that in the condition of the combination between plate and roller surface, the size of deformation is based on the roller and the guiding groove on roller surface affects the deformation of piate, which in reality reflects the working state. The purpose was to provide theoretical basis for design and optimization of CTP imaging drum.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第21118060位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号