文章摘要
齐明思,刘守君,赵奇,张峰.基于 Ansys/LS-DYNA的缓冲气囊着陆过程仿真研究[J].包装工程,2014,35(11):13-17.
QI Ming-si,LIU Shou-jun,ZHAO Qi,ZHANG Feng.Simulation Research of the Cushioning Airbag during the Landing Process Based on Ansys/LS-DYNA[J].Packaging Engineering,2014,35(11):13-17.
基于 Ansys/LS-DYNA的缓冲气囊着陆过程仿真研究
Simulation Research of the Cushioning Airbag during the Landing Process Based on Ansys/LS-DYNA
投稿时间:2014-03-14  修订日期:2014-06-01
DOI:
中文关键词: 硬式气囊  缓冲  仿真  Ansys/LS-DYNA
英文关键词: rigid airbag  cushion  simulation  Ansys/LS-DYNA
基金项目:国家自然科学基金资助项目(51275486)
作者单位
齐明思 中北大学 太原 030051 
刘守君 中北大学 太原 030051 
赵奇 中北大学 太原 030051 
张峰 中北大学 太原 030051 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 以冲压式快速空投硬式气囊为研究对象, 对气囊以特定角度着陆时的缓冲过程进行仿真分析。 方法 使用 SolidWorks 软件建立气囊的仿真模型, 然后使用 Ansys/LS-DYNA 有限元分析软件,分别从气囊的材料定义、有限元模型的构建和仿真结果分析等方面进行仿真研究, 并得出冲压式快速空投气囊着陆过程中应力应变的动态参数, 以及货物和气囊的冲击加速度波动曲线。 结果 气囊在偏离竖直轴 15° 着陆缓冲过程中 , 在 0.077 207 s 时, 地面与气囊的棱接触处受到的最大应力为 1.47MPa, 此时对应的最大应变为 0.479 614 m。 结论 冲压式快速空投气囊在偏离竖直轴 15° 着陆时, 气囊所受的最大冲击应力以 1.47 MPa为标准, 可更好地确定空投物体的质量, 并且可以针对性地加强对气囊应力应变较大区域的防护,防止气囊在冲击过程中破坏。
英文摘要:
      Objective This paper took a punched quick airdrop airbag as the research object, and simulated its cushioning process during the landing process at a certain angle. Methods The paper established a simulation model of the airbag through SolidWorks software and used the finite element analysis software Ansys/LS-DYNA to simulate the landing process from the aspects of airbag material definition, construction of finite element model and simulation results analysis. The dynamic parameters of the stress and strain of the airbag during the landing process of the punched quick airdrop airbag as well as the impact acceleration curve of the goods and airbag were obtained. Results During the landing process of the punched quick airdrop airbag with 15° deviation from the vertical shaft, the maximum stress value of the airbag was 1.47 MPa and the corresponding maximun strain value was 0.479 614 m at the contacting edge of the airbag with the ground at 0.077 207 s. Conclusion When the punched quick airdrop airbag landed at an angle of 15° deviated from the vertical shaft, the biggest impact should use 1.47 MPa as a standard. As a result, the mass of airdrop body can be better specified, and the protection of the area with great stress and strain to the airbag from being damaged during the process of impact could be strengthened.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第21005403位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号