文章摘要
张文雨,许文才,罗世永,张能健,李绍国,邓刚.胶印联机冷烫胶黏剂的性能要求分析[J].包装工程,2016,37(9):161-164,170.
ZHANG Wen-yu,XU Wen-cai,LUO Shi-yong,ZHANG Neng-jian,LI Shao-guo,DENG Gang.Performance Requirements Analysis of Adhesive Used for the Online Cold Stamping in the Offset Printing Line[J].Packaging Engineering,2016,37(9):161-164,170.
胶印联机冷烫胶黏剂的性能要求分析
Performance Requirements Analysis of Adhesive Used for the Online Cold Stamping in the Offset Printing Line
投稿时间:2015-09-03  修订日期:2016-05-10
DOI:
中文关键词: 胶印联机冷烫  胶黏剂  粘性  乳化率  粘弹性  冷烫印质量
英文关键词: online cold stamping in the offset printing line  adhesive  tack  emulsion  viscoelasticity  quality of the online cold stamping
基金项目:北京印刷学院科研能力提高项目
作者单位
张文雨 北京印刷学院北京 102600 
许文才 北京印刷学院北京 102600 
罗世永 北京印刷学院北京 102600 
张能健 东莞虎彩印刷有限公司东莞 523925 
李绍国 绍兴虎彩激光材料科技有限公司绍兴 312000 
邓刚 绍兴虎彩激光材料科技有限公司绍兴 312000 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 获得胶印联机冷烫用胶黏剂的性能和冷烫印质量的关系, 提出胶印联机冷烫用胶黏剂的性能要求。方法 选用一种商用胶印联机冷烫胶黏剂, 测试黏度、 粘弹性、 触变性、 乳化率、 粘性、 干燥速率和固含量, 分析其与冷烫印质量的关系。结果 冷烫胶黏剂的初粘性要高并维持稳定, 且具有较快的干燥速率。印刷适性如黏度、 粘弹性、 触变性、 乳化率和普通胶印油墨要求相近, 在保证印刷适性、 粘性和合适的干燥速率的前提下, 固含量越高越好。结论 研究结果可为胶印联机冷烫胶黏剂的改进和胶印冷烫质量的提高提供参考。
英文摘要:
      The aims of this study was to obtain the relationship between the performance of adhesive and cold stamping quality, and to put forward the performance requirements of adhesive used for the online cold stamping in the offset printing line. The performance parameters such as viscosity, viscoelasticity, thixotropy, emulsification ratio, tack value, drying rate and solid content of a commercial adhesive for online cold stamping were tested. The relationship between the performance of adhesive and cold stamping quality was analyzed. The tack value of the adhesive should be large and kept stable. The drying rate should be quick. Printability requirements such as viscosity, viscoelasticity, thixotropy, emulsification ratio of the adhesive were the same as those of the common offset printing ink. On the premise of appropriate printability, tack value, drying rate, higher solid content of the adhesive was always better. The results would provide reference for improvement of adhesive and quality of online cold stamping in the offset printing line.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第21350258位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号