文章摘要
焦凡苇,梁海龙.3-UPU柔顺并联机构构型拓扑优化设计与实验测试[J].包装工程,2019,40(5):187-195.
JIAO Fan-wei,LIANG Hai-long.Topology Optimization Design and Experimental Test of 3-UPU Compliant Parallel Mechanism[J].Packaging Engineering,2019,40(5):187-195.
3-UPU柔顺并联机构构型拓扑优化设计与实验测试
Topology Optimization Design and Experimental Test of 3-UPU Compliant Parallel Mechanism
投稿时间:2018-10-29  修订日期:2019-03-10
DOI:10.19554/j.cnki.1001-3563.2019.05.026
中文关键词: 旋量与逆螺旋理论  微分Jacobian矩阵  拓扑优化技术  实验测试
英文关键词: wrench and reciprocal screw theory  differential Jacobian matrix  topology optimization technology  experimental test
基金项目:
作者单位
焦凡苇 中北大学朔州校区 能源与机械工程管理部朔州 036000 
梁海龙 中北大学朔州校区 能源与机械工程管理部朔州 036000 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 为了设计出具有x,y和z方向纯平动的微纳级精密定位装置。方法 首先,运用旋量与逆螺旋理验证所设计的传统3-UPU并联机构运动特性;采用封闭矢量映射原理构建3-UPU并联机构的微分Jacobian,实现各关节与动平台的空间映射关系。然后,定义优化问题的目标函数为结构刚度,约束函数为体积比,运动特性条件为微分Jacobian构造3-UPU柔顺并联机构的SIMP模型,并运用优化算法计算。最后,基于Ossmooth对优化构型进行CAD模型的提取,完成运动特性的力学仿真分析,此外,通过3D打印制造处理后的CAD模型,并完成运动特性的实验测试。结果 仿真可得,优化后的构型柔度值从58.324 mm/N下降到25.993 mm/N;一阶固有频率从964.64 Hz提高到1362.26 Hz;沿x,y和z方向的微运动特性分别达到2.488,6.512,9.185 μm;3-UPU柔顺并联机构优化构型的微运动特性与理论解处于同一微米级,并运用实验测试进行了验证。结论 拓扑优化设计的构型具有微米级运动特性和微米定位精度,实验测试结果验证了该优化技术的可行性。
英文摘要:
      The work aims to design a micro-nano precision positioning device with pure translational motion along x, y and z direction. Firstly, the screw and reciprocal screw theory were used to verify the kinetic characteristic of the designed traditional 3-UPU parallel mechanism. The closed vector mapping principle was adopted to construct the differential Jacobian of 3-UPU parallel mechanism to realize the spatial mapping relation between the joints and the moving platform. Then, the objective function used to optimize problem was defined as structural stiffness and constraint function as the volume ratio. The kinetic characteristic condition was the SIMP model of 3-UPU compliant parallel mechanism built by differential Jacobian and solved by optimization algorithm. Finally, the CAD model was extracted for optimized configuration based on Ossmooth, and the mechanical simulation analysis of the kinetic characteristics was completed. Furthermore, the processed CAD model was produced by 3D printing, and the experimental test of kinetic characteristics was completed. Through simulation, the compliance value of the optimized configuration declined from 58.324 mm/N to 25.993 mm/N, the first order natural frequency increased from 964.64 Hz to 1362.26 Hz, the micro kinetic characteristics along x, y and z direction reached 2.488, 6.512 and 9.185 μm respectively and the micro kinetic characteristics of the optimal configuration of 3-UPU compliant parallel mechanism was at the same micron level as the theoretical solution, which was verified by experimental test. Configuration of the topological optimization design has micron kinetic charac-teristics and micron positioning accuracy, and the feasibility of the optimization technique is verified by the experimental results.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第20789767位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号