文章摘要
孙德强,李钟波,李国志,段世非,白家华,张帆,李清.基于特征单元的三角形蜂窝异面压缩的有限元分析[J].包装工程,2019,40(19):80-85.
SUN De-qiang,LI Zhong-bo,LI Guo-zhi,DUAN Shi-fei,BAI Jia-hua,ZHANG Fan,LI Qing.Finite Element Analysis on Out-of-plane Compression of Triangular Honeycomb Based on Representative Cells[J].Packaging Engineering,2019,40(19):80-85.
基于特征单元的三角形蜂窝异面压缩的有限元分析
Finite Element Analysis on Out-of-plane Compression of Triangular Honeycomb Based on Representative Cells
投稿时间:2019-04-23  修订日期:2019-10-10
DOI:10.19554/j.cnki.1001-3563.2019.19.011
中文关键词: 三角形蜂窝  有限元分析  压缩性能  异面
英文关键词: triangular honeycomb  finite element analysis  compression property  out-of-plane
基金项目:国家自然科学基金(51575327);陕西省教育厅重点实验室及基地项目(16JS014);陕西省教育厅2014陕西本科高校专业综合改革试点子项目(陕教高[2014]16号)
作者单位
孙德强 陕西科技大学 a.陕西省造纸技术与特种纸品开发重点研究室 b.中国轻工业纸基功能材料重点实验室 c.轻化工程国家级实验教学示范中心西安 710021 
李钟波 陕西科技大学 a.陕西省造纸技术与特种纸品开发重点研究室 b.中国轻工业纸基功能材料重点实验室 c.轻化工程国家级实验教学示范中心西安 710021 
李国志 陕西科技大学 a.陕西省造纸技术与特种纸品开发重点研究室 b.中国轻工业纸基功能材料重点实验室 c.轻化工程国家级实验教学示范中心西安 710021 
段世非 陕西科技大学 a.陕西省造纸技术与特种纸品开发重点研究室 b.中国轻工业纸基功能材料重点实验室 c.轻化工程国家级实验教学示范中心西安 710021 
白家华 陕西科技大学 a.陕西省造纸技术与特种纸品开发重点研究室 b.中国轻工业纸基功能材料重点实验室 c.轻化工程国家级实验教学示范中心西安 710021 
张帆 陕西科技大学 a.陕西省造纸技术与特种纸品开发重点研究室 b.中国轻工业纸基功能材料重点实验室 c.轻化工程国家级实验教学示范中心西安 710021 
李清 陕西科技大学 a.陕西省造纸技术与特种纸品开发重点研究室 b.中国轻工业纸基功能材料重点实验室 c.轻化工程国家级实验教学示范中心西安 710021 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 研究三角形蜂窝排列方式对三角形蜂窝异面动态压缩性能的影响。方法 借助Ansys/LS-DYNA建立基于特征单元的三角形蜂窝异面动态压缩的有限元分析模型,研究三角形蜂窝排列方式对三角形蜂窝异面压缩性能的影响。结果 将三角形蜂窝胞元阵列模型的有限元分析结果与理论值进行对比,证明三角形蜂窝的有限元模型是可靠的,随后将三角形胞元阵列模型与此研究中采用的特征单元模型计算结果进行对比,结果显示2种有限元计算模型的计算结果一致,证明此研究特征单元结构的选取和模型的建立是可靠的。结论 不同排列方式对三角形蜂窝在异面方向上的动态峰应力和单位体积能量吸收没有影响。
英文摘要:
      The work aims to study the influence of triangular honeycomb arrangement on the dynamic compression properties in the out-of-plane direction of triangular honeycomb. By means of Ansys/LS-DYNA, a finite element analysis model of triangular honeycomb's out-of-plane dynamic compression based on representative cells was established, and the influence of triangular honeycomb arrangement on the out-of-plane compression properties of triangular honeycomb was studied. Comparing the finite element analysis results of the triangular honeycomb whole cell array model with the theoretical values, it was proved that the finite element model of the triangular honeycomb was reliable. Then, the triangular whole cell array model was compared with the calculated results of the representative cell model used in this study. The results showed that, the calculated results of the two finite element calculation models were consistent, which proved that the selection of the representative cell structure and the establishment of the model in this study were reliable. Different arrangements have no effect on the dynamic peak stress and energy absorption per unit volume of triangular honeycomb in the out-of-plane direction.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第21377855位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号