文章摘要
李国志,刘鸿梅,孙德强,李彬,石威.步进电机驱动器和EPE衬垫配合间隙与振动关系[J].包装工程,2021,42(5):142-147.
LI Guo-zhi,LIU Hong-mei,SUN De-qiang,LI Bin,SHI Wei.Relationship between Vibration and Fit Clearance of Stepper Motor Driver and EPE Cushion Foam[J].Packaging Engineering,2021,42(5):142-147.
步进电机驱动器和EPE衬垫配合间隙与振动关系
Relationship between Vibration and Fit Clearance of Stepper Motor Driver and EPE Cushion Foam
投稿时间:2020-08-28  
DOI:10.19554/j.cnki.1001-3563.2021.05.018
中文关键词: 步进电机驱动器  EPE衬垫  配合间隙  振动关系
英文关键词: stepper motor driver  EPE cushion foam  fit clearance  vibration relationship
基金项目:国家自然科学基金(51575327);陕西省教育厅重点实验室及基地项目(16JS014);陕西省教育厅 2014 陕西本科高校专业综合改革试点子项目(陕教高[2014]16号)
作者单位
李国志 陕西科技大学 陕西省造纸技术及特种纸品开发重点实验室西安 710021
陕西科技大学中国轻工业纸基功能材料重点实验室西安 710021
陕西科技大学轻化工程国家级实验教学示范中心西安 710021 
刘鸿梅 陕西科技大学 陕西省造纸技术及特种纸品开发重点实验室西安 710021
陕西科技大学中国轻工业纸基功能材料重点实验室西安 710021
陕西科技大学轻化工程国家级实验教学示范中心西安 710021 
孙德强 陕西科技大学 陕西省造纸技术及特种纸品开发重点实验室西安 710021
陕西科技大学中国轻工业纸基功能材料重点实验室西安 710021
陕西科技大学轻化工程国家级实验教学示范中心西安 710021 
李彬 陕西科技大学 陕西省造纸技术及特种纸品开发重点实验室西安 710021
陕西科技大学中国轻工业纸基功能材料重点实验室西安 710021
陕西科技大学轻化工程国家级实验教学示范中心西安 710021 
石威 陕西科技大学 陕西省造纸技术及特种纸品开发重点实验室西安 710021
陕西科技大学中国轻工业纸基功能材料重点实验室西安 710021
陕西科技大学轻化工程国家级实验教学示范中心西安 710021 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 为确定步进电机驱动器和EPE衬垫的配合间隙与振动的关系。方法 选取步进电机驱动器为研究对象,以密度为20,28,32 kg/m3的EPE衬垫为隔振包装,研究对象与衬垫在垂直方向的配合间隙为4,−2,0,2,4 mm。定制木质夹具的密度为32 kg/m3,配合间隙为−4 mm的EPE衬垫模型,参照ASTM-D4169随机振动试验部分的PSD功率谱密度曲线,进行随机振动试验分析。依据试验结果,修正该包装件的仿真模型、接触方式、网格划分等,仿真结果与试验结果的RPSD曲线吻合程度良好。依据该包装件的仿真设置,对密度为20,28 kg/m3的系列配合包装件进行仿真分析。结果 同一密度EPE衬垫,间隙配合比过盈配合振动强度低,0 mm配合的RMS值最小,振动强度最低。同一配合间隙,过盈配合时,EPE衬垫密度越低,RMS值越小,振动强度越低;间隙配合时,EPE衬垫密度越高,RMS值越低,振动强度越低。结论 采用EPE衬垫包装步进电机驱动器时,在同密度衬垫和同量级的外界激励下,0 mm配合隔振性能最佳,间隙配合隔振性能优于过盈配合。
英文摘要:
      The work aims to determine the relationship between vibration and fit clearance of stepper motor driver and EPE cushion foam. The stepper motor drivers were selected as the research product and EPE cushion foam with densities of 20, 28 and 32 kg/m3 were used as vibration isolation packaging. The fit clearance between the product and the EPE cushion foam in the vertical direction was −4, −2, 0, 2 and 4 mm. Customized wooden fixture and EPE cushion foam model with the density of 32 kg/m3 and the fit clearance of −4 mm were used for random vibration test analysis according to the PSD power spectral density curve of American ASTM-D4169. According to the test results, the simulation model, contact, mesh generation, etc. of the corresponding type of package were modified until the simulation results were in good agreement with the RPSD curve of the test results. According to the simulation setting of the package, the series of fit packages with densities of 20 and 28 kg/m3 were simulated and analyzed. For the EPE cushion foam with the same density, the vibration intensity of clearance fit was lower than that of interference fit. The RMS value and vibration intensity were the lowest at 0 mm fit. For the same fit, the lower the EPE cushion foam density was, the smaller the RMS value was and the lower the vibration intensity was at interference fit. The higher the EPE cushion foam density was, the smaller the RMS value was and the lower the vibration intensity was at clearance fit. When EPE cushion foam is used to pack the stepper motor driver, the vibration isolation performance of 0 mm fit is the best and the vibration isolation performance of clearance fit is better than that of interference fit under the same density of EPE cushion foam and level of external excitation.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第22496180位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号