文章摘要
李玉华,王文雅,蒙磊,李光.方罐盖注胶烘干机罩边机构有限元分析及优化设计[J].包装工程,2016,37(7):120-124.
LI Yu-hua,WANG Wen-ya,MENG Lei,LI Guang.Finite Element Analysis and Optimization Design of Cover Edge Mechanism for Square Tin Cover Glue-injection and Drying Machine[J].Packaging Engineering,2016,37(7):120-124.
方罐盖注胶烘干机罩边机构有限元分析及优化设计
Finite Element Analysis and Optimization Design of Cover Edge Mechanism for Square Tin Cover Glue-injection and Drying Machine
投稿时间:2015-06-23  修订日期:2016-04-10
DOI:
中文关键词: 方罐盖  罩边机构  上压板结构  有限元分析  优化设计
英文关键词: square tin cover  cover edge mechanism  up plate structure  finite element analysis  optimization design
基金项目:
作者单位
李玉华 天津市奥恒机电装备有限公司天津 300380 
王文雅 天津科技大学天津 300222 
蒙磊 天津天狮学院天津 301700 
李光 天津科技大学天津 300222 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 研究方罐盖注胶烘干机罩边机构在复杂应力作用下的静态和动态特性, 并进行优化设计。方法 通过Ansys Workbench建立罩边机构三维模型, 应用有限元分析方法对上压板结构进行静态分析和模态分析; 建立优化数学模型, 对比分析优化前后结果。结果 通过分析获得了优化前后的应力云图、 变形云图以及模态振型图。优化后的上压板厚度减小了30%, 宽度减小了7%, 变形量等效应力增加, 固有频率有所减少, 质量减轻了约7.1 kg。结论 经分析, 罩边机构上压板的结构优化是合理的, 在保证强度和刚度的条件下, 减少质量并节约成本。
英文摘要:
      This experiment researched the static and dynamic characteristics and made an optimization design of cover edge mechanism for square tin cover glue-injection and drying machine. The 3D model of cover edge mechanism was created by Ansys Workbench, and the method of finite element analysis was used for the static analysis and modal analysis of up plate structure. The optimization mathematic model was created and the analytical results before and after optimization were compared. Through the analysis, the stress and deformation before and after optimization and the modal vibration mode were obtained. The up plate thickness after optimization decreased by 30%, and the width reduced by 27%, while the equivalent stress deformation increased, the natural frequency reduced, and the quality decreased by about 7.1 Kg. The analysis showed the optimization of up plate structure was reasonable, and the quality was reduced and the cost was saved in the condition of ensuring the strength and rigidity.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第22612420位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号